File format · .m7
M7 File Format (Farallon MacRecorder 7 kHz): Repair and Recovery
M7 files hold 7 kHz mono audio digitized by Farallon's MacRecorder on classic Macintosh. Learn what breaks them and how the sound can be recovered.
The .m7 extension marks a monophonic sound recording captured through Farallon's MacRecorder digitizer on a classic Macintosh. The 7 in the name refers to the 7,000 Hz sampling rate the device used. Support for the format has all but disappeared, so healthy files are routinely mistaken for damaged ones.
What is an M7 file?
An M7 file holds digitized audio from the MacRecorder, a small digitizer that Farallon Computing sold for the Macintosh in the late 1980s. The device attached to the Mac's serial port and converted microphone or line input into digital sound. Farallon's bundled software handled the recording, and SoundEdit, an editor first published by MacroMind, could drive the hardware as well.
The format is proprietary and was never publicly documented. We know of no registered MIME type, no file signature, and no formal specification for it. Extension references describe it simply as Farallon MacRecorder format sampled at 7 kHz. Where a definitive answer matters, the vendor's own documentation would be authoritative, and little of it survives today.
Sound quality was modest by design. Classic Macintosh audio was eight-bit mono, and a 7 kHz recording sits close to a good telephone call. That suited voice notes, narration, and simple effects, which is what most owners recorded.
Inside an M7 file
The container wraps a stream of raw sound samples in a layout specific to the MacRecorder software. A header describes what a player needs to know: the sampling rate, the channel count, and the length of the recording. The samples themselves are the payload, and they stay readable even when the header does not.
Two things make these files predictable to work with. The extension itself states the sampling rate, and the recording is mono. At one byte per sample, a minute of sound occupies roughly 420,000 bytes, or about 410 KB. A file whose size matches no sensible duration at that rate is truncated or padded.
Classic Macintosh files also carried structure outside their bytes. The catalog stored a type and creator code for every file, and many formats split content across a data fork and a resource fork. Moving an M7 file to another system without preserving that context can discard information silently.
Is the file damaged, or just unsupported?
Most M7 files that refuse to open are perfectly healthy. Modern players such as VLC and QuickTime offer no decoder for the MacRecorder container, and their failure message looks exactly like the one a corrupt file produces. Test the recording in an environment that understands it first. A classic Mac OS emulator such as Basilisk II or SheepShaver, running the original software, settles the question in minutes. If the sound plays there, the file needs converting, not repairing.
Genuine damage looks different. The file may appear with a size of zero bytes. Tools may report unknown duration or missing properties because the header will not parse. Playback may stop partway through, or collapse into clicks and stretches of silence. Those symptoms point to real loss of data.
What actually damages these files?
Age is the leading cause. The 800 KB floppy disks of that era lose their magnetic coating after decades, and a single faded sector can cut a recording short. Hard drive crashes, interrupted copies, and directory damage on the original disk produce the same result.
Transfer method matters too. Copying a legacy Mac file to a modern filesystem can drop its resource fork and type codes. The copy then looks complete, and the sound may still be inside it, but software that expected the missing pieces will reject the file. That loss is recoverable more often than not.
What can be recovered from a damaged file?
The outlook is better than with many formats, because the audio is a raw sample stream rather than a tightly compressed one. If the samples survive, the sound can be rebuilt even without any header. The sampling rate comes from the extension, the channel count is one, and the duration follows from the byte count.
Expectations should match the source. Sampling at 7,000 Hz captures nothing above about 3,500 Hz. Speech and narration usually come through clearly, since the elements that make speech intelligible sit well below that line. Music will sound muffled, because those high frequencies were never recorded.
Sections of samples that are gone cannot be reinvented. We mark those gaps, splice around them, and note their positions so you know exactly what survived.
Our recovery process
We start by confirming what the file actually is. Hexadecimal inspection shows whether the data matches MacRecorder output and where the damage sits. From there the work follows a consistent sequence.
- Preserve the source. Every step happens on a byte copy or a disk image, never on your original media.
- Rebuild the parameters. The rate, the mono channel count, and the sample width come from the format itself and any surviving header.
- Extract the samples. The raw stream is lifted out and re-wrapped as a standard WAV or AIFF file.
- Repair the joins. Fragments are ordered, gaps are logged, and the final size is checked against the expected duration.
You receive a modern file plus a short report describing anything that could not be saved.
Frequently asked questions
Can I convert an M7 file by renaming it to .wav?
No. Renaming changes nothing inside the file. A WAV file has its own header and layout, which players read from the bytes themselves. Conversion must be done by software that understands both layouts, or by a specialist when the file is damaged.
Why does every player tell me the file is broken?
A player cannot tell the difference between a format it does not know and a format it knows but cannot parse. Both produce an open failure. The emulator test described above answers the question quickly.
How should I move M7 files off an old Mac?
Keep each file inside a disk image, or encode it with MacBinary, so the forks and type codes survive the trip. Dragging a bare file to modern storage can silently discard parts of it.
Is audio from a 7 kHz recording worth recovering?
Often yes. Speech and narration remain clear and usable, and for archival or family-history purposes that is usually the whole point. Music will be dull, since frequencies above 3,500 Hz were never captured in the first place.
Do you need the original MacRecorder hardware?
No. Recovery works from the bytes already in the file. The hardware would only matter for re-recording, and re-recording cannot rescue audio that is already digital.
Get a free evaluation
If you have MacRecorder recordings trapped on aging disks, or M7 files that nothing will open, send us a copy for a free evaluation. Our engineers will inspect the data and tell you plainly what is recoverable before any paid work begins. See our sound file repair service for details.
Send us your .m7 file for a free evaluation
Our recovery engineers will tell you exactly what can be recovered — at no cost. There is no charge if we cannot recover your data.
Start a free evaluation